International Customers: Dial US Country Code, followed by the phone or fax numbers listed below or e-mail specific product inquiries to Customer Support address. For general inquiries, please use the General Information e-mail address. We will respond promptly for standard product inquiries.
Telephone Toll Free
USA and Canada Only:
1-877-777-2629
Local Telephone
973-575-0760
973-276-1931
FAX
973-575-0431
Postal address
Fluorotherm Polymers Inc.
333 New Road
Parsippany, NJ 07054
Electronic mail:
sales@fluorotherm.com
Customer Support: sales@fluorotherm.com
Send mail to webmaster@fluorotherm.com with questions or comments about this web site.
Fluorotherm introduces corrosion resistant load bearing metal rods; with complete encapsulation in PTFE, FEP, PFA. These rods may be used to support work in a corrosive environment such as a plating or coating bath, as carrier to transport work in a chemically agressive environment and in numerous other uses. The rigidity of the metal core provides strength that cannot be matched by plastic rods. A PTFE or other adapter of appropriate configuration over the encapsulated rod can be used as points of support. This encapsulated construction provides the strength of metal and the chemical resistance of Teflon® type materials. Such construction can bear upto 700 lb loads in nitric, HF; hydrochloric and sulfuric acid baths and other hazardous atmospheres. The complete fluoropolymer encapsulation is distinctly superior to heat shrink tube covering where the wall thickness is too light to sustain reasonable loads or abrasive wear, without tearing or cracking. The high continuous use temperature of PTFE, FEP or PFA permits these materials to be used up to 400 deg F.
Fluorotherm is now able to provide rapid turnaround times for a wide range of colored tubing in standard and custom sizes. For the range of industrial sizes commonly available, please see our listing under "Tubing Products". Tubing is available in PTFE, FEP, ETFE and PFA materials. The product is shipped as rolls (coils) or in spools, if required, for sizes under 1/2" OD. While PTFE tubing is supplied in production lengths due to the batchwise production process, other materials are available in long continuous lengths, as required by customer. Color bases and loading unformity is carefully monitored so as not to detract from the inherent unique thermal resistance, chemical inertness and electrical properties of PTFE, FEP and PFA. These properties are lsited under "Detailed Properties" on our website homepage. RoHS certifications are supplied with colored tubing, as applicable.
Read the Newsletter: Volume 1, July 2007 
Click here to See Fluorotherm Heat Exchangers in Action.
Fluorotherm invests in new production facility to support customer demand for quicker deliveries.
Fluorotherm has invested in a new facility, with trained personnel, to support increased production, with a wider capability than before. The new production capability will facilitate our quick turnaround at competitive cost to our customers. For additional information on please contact sales@fluorotherm.com or call 1-877-777-2629.
Fluorotherm announces a new addition of PVDF frame Immersion Heat Exchanger coils to our family of Immersion coil products. This addition significantly broadens the performance range of our line of products, currently consisting of low temperature Polypropylene frame (to 150° F) and high temperature, premium PTFE frames. Of course, the standard tubing coils of the heat exchangers still consist of either FEP (to steam pressures of 2 bar / 30 psig) or PFA tubing (4 bar or 60 psig). Higher steam pressure tubing is also available with custom sized fluoropolymer heat exchanger tubing.
PVDV frame heat exchangers, now in place for two years at selected customer sites are superior in performance to Polypropylene frames, in cases where the tank or bath temperatures exceed 150° F, and can operate up to temperatures of 210° F. PTFE frame temperatures are recommended for temperatures above 210° F.
Fluorotherm has successfully developed and installed multiple fluoropolymer coil shell and tube heat exchangers with significant increase in the heat transfer surface area from 12 sq.ft (1.1 sq.mt) to 55 sq.ft (5.1 sq.mt). Tubing is available in FEP, PFA, High Purity PFA and PTFE materials. Popular shell side materials are PVC and CPVC., although Stainless steel is also available for special high temperature shell side fluid applications.
Contact Fluorotherm to find out whether our products are suited to your application.
